Results 1 to 3 of 3

Thread: Creating Medusa With Photo Manipulation P.1

  1. #1
    Join Date
    Aug 2011
    Posts
    14

    Creating Medusa With Photo Manipulation P.1

    Creating Medusa With Photo Manipulation



    Images Used

    Here is a list of the various images used to create this piece:
    http://www.sxc.hu/photo/797762
    http://www.sxc.hu/photo/1063321
    http://www.sxc.hu/photo/1068537
    http://www.sxc.hu/photo/1056935
    http://www.sxc.hu/photo/1061420
    http://www.sxc.hu/photo/1060564
    http://www.sxc.hu/photo/1053704
    http://www.sxc.hu/photo/999039
    http://www.sxc.hu/photo/995347
    http://www.sxc.hu/photo/792891
    http://www.sxc.hu/photo/704414
    http://www.sxc.hu/photo/586141
    http://www.sxc.hu/photo/1066166
    Step 1

    Open up a new document and paste in an image of a woman’s face. Move it so that the face is in the bottom section of the document.

    Step 2

    Now cut out the woman’s face using the lasso tool. Select your whole canvas and then paste her in to paste her into the center of your canvas. Then shift her down towards the bottom of your document. I also created a dark gray background layer beneath my face layer.

    Step 3

    Now duplicate your ‘face’ layer and hide the original. This is because we’ll be applying destructive techniques to it. Then go to image>adjustments>shadows/highlights and apply the settings shown below:

    Step 4

    Now go to image>adjustments>hue/saturation and apply the settings shown below:

    Step 5

    Now go to image>adjustments>color balance. The trick with these steps is to be fairly subtle, as if you apply anything too heavily it will cause the image to look fake.

    Step 6

    Now duplicate your ‘face’ layer and set the duplicate’s blend mode to ‘hard light’. This should give your face a lot more intense shadows. To heighten the shadows again duplicate this new ‘hard light’ layer.

    Step 7

    Now paste an image of some snake scales into a new layer above your face layers. Go back to your face layer and click somewhere around it using the magic wand tool (this selects the area around the woman’s face), then return to your scales layer and hit delete. This should leave scales only covering the woman’s face, and none of the background. Then set this layer’s blend mode to ‘multiply’ and reduce it’s opacity to around 60%.



    More: http://cs5tutorial.net/creating-medu...nipulation-p-1

  2. #2
    Join Date
    Aug 2011
    Posts
    14
    Step 8

    Now create a new layer above your hard light face layers and below your scales layer called ‘shadows’. Select a smallish, soft black paintbrush and set it’s opacity to 10%. Then paint over the areas of existing shadow in the woman’s face (around the eyes, under the nose, the sides of the face etc…). You could heighten the shadows a number of ways, but this way really gives you the most control.

    Step 9

    Now paste in an image of a snake. Cut the snake out very carefully using the lasso tool. By the way… this should probably be a good time to tell you that I really don’t like snakes. Dumbest idea for a tutorial ever…
    Anyway, then resize/rotate the image to fit nicely onto the top of the woman’s head. Then duplicate this layer and go to edit>transform>flip horizontal. Move the flipped duplicate to be symmetrical on the other side of the woman’s head.


    Step 10

    Now go to image>adjustments>hue/saturation and apply the settings below to make the snakes blend in a little better with the woman’s head.


    Step 11

    The scales over the woman’s face are looking a little intense right now. To fix this I select a large, soft eraser brush at 10% and erase away parts of the scales to create the impression that they are gradually coming in from the sides of her face.
    I also made the two snakes blend a little better with the woman’s face by first going to image>adjustments>brightness/contrast and upping the contrast. Then I reduced the saturation and darkened the layer a little.

    Step 12

    I repeat the same technique that I used to place the original snakes to place two new ones on a new layer above the cobras layer. Again, I reduce the saturation and play around with brightness/contrast until the images blend nicely with the rest of the image. Then I take a large, soft eraser brush and erase away the bottom of the snakes so that they appear to be growing from the woman’s head.

    Step 13

    Now duplicate this new snake layer and move the duplicate behind the cobras layer. The trick is to interweave the various snakes so that they appear to be part of the same mass of ‘hair’. Once you’ve moved the duplicate layer go to edit>transform>scale and then in the options bar (above your canvas) change the width/height of the object to 90%. This will resize your duplicate snakes to 90% of their original size, but will keep them centered in your canvas. Then simply move the snakes up so that they are above your original snakes. Repeat this process again, moving your second duplicate behind the first duplicate layer.

    Step 14

    Now I add some more snakes, trying to fit them together nicely. It would take far too long to explain the exact steps that I used to make them blend together reasonably well, so I’ll try and give a few pointers…
    If an object is looking too light, then reduce it’s brightness.
    If it’s looking washed out or flat then up it’s contrast.
    If it’s looking too bright then reduce it’s saturation.
    These are pretty basic techniques, and a lot more can be done. However, for this stage of the work it’s really sufficient to get the various photos blending together fairly well.

    Step 15

    Now add a LOT more snakes. Use the same basic principles of duplicating/flipping, and then reducing saturation/brightness where necessary. Try to completely surround the woman’s face with snakes, and arrange them in a creative way, keeping track of layer orders.

    Step 16

    If you remember we originally created a dark gray background. Select your background layer and then fill it with solid black. If you look at the previous step’s image you will see that some of the edges of the woman’s face don’t blend well into the black background. To fix this create a new layer called ‘shadows merge’ above your face layers (and scale overlay layer). Use a small, soft black paintbrush at 10% to gently brush the edges of the face into the background. You can see an example of the areas that I blended below:

    Incoming search terms:

    Next: http://cs5tutorial.net/creating-medu...nipulation-p-3

  3. #3
    Join Date
    Jun 2012
    Location
    usa
    Posts
    86
    want some more detail about this post...........


    Real Kanban

Similar Threads

  1. Creating a photo gallery
    By br14nl in forum Web Design, HTML Reference and CSS
    Replies: 0
    Last Post: 21 Jul 2010, 01:57 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •